News
-
26-10-07Limit Switch Symbols: IEC and Ladder Diagram ExamplesRead limit switch symbols, distinguish NO and NC reference states from PLC Boolean tests, and verify the exact device and drawing. -
26-10-06AC vs DC Relay Coils: Selection and Common MistakesSeparate AC and DC coil requirements from contact ratings. Check voltage, frequency, power, suppression, release, and replacement compatibility. -
26-10-06Flyback Diodes for DC Relay Coils: Selection and ReleaseUnderstand DC relay coil flyback diodes, polarity, driver protection, built-in suppression, selection data, and release-time trade-offs. -
26-10-06Limit Switch Wiring: NO, NC and Changeover ContactsIdentify COM, NO and NC from the exact diagram, compare feedback paths, check controller interfaces, and verify actuator and machine response. -
26-10-05Three-Position Selector Switch Wiring for Hand–Off–AutoBuild a Hand–Off–Auto contact plan, distinguish controller and coil circuits, and check each mode, transition, and restart condition. -
26-10-05Two-Position Selector Switch Wiring for Hand–Off ControlPlan two-position Hand–Off control from the exact contact table, input or coil circuit, load rating, installation, and verified machine response. -
26-10-05Relay Contact Arcing: Causes and Suppression MethodsLearn why relay contacts arc, how load type affects suppression, and what to verify before adding an RC network, diode, MOV, or TVS. -
26-10-04Relay Failure Modes: Coil, Contacts and Mechanical WearClassify relay failures before replacing parts. Review coil supply, contact load, release behavior, socket faults, environment and failure evidence. -
26-10-04Momentary vs Latching Capacitive Touch SwitchesCompare touch-following and retained outputs. Define event logic, supply and input interfaces, startup, power restoration, indication and testing. -
26-10-04Flashing vs Steady Indicator Lights for Machine AlarmsChoose flashing or steady machine indications from a clear state matrix. Define operator action, acknowledgement, lamp interfaces and visibility. -
26-10-03AC vs DC Indicator Lights: Matching the Panel SupplyMatch a panel indicator to its declared AC or DC supply. Check exact variants, polarity, electronic outputs, leakage and the intended signal. -
26-10-03Indicator Light Symbols in Electrical SchematicsRead indicator lamp and LED symbols with device tags, supply notes, terminal maps and feedback sources. Match the drawing to the actual panel lamp.
-
07
26-10Limit Switch Symbols: IEC and Ladder Diagram ExamplesRead limit switch symbols, distinguish NO and NC reference states from PLC Boolean tests, and verify the exact device and drawing.
-
06
26-10AC vs DC Relay Coils: Selection and Common MistakesSeparate AC and DC coil requirements from contact ratings. Check voltage, frequency, power, suppression, release, and replacement compatibility.
-
06
26-10Flyback Diodes for DC Relay Coils: Selection and ReleaseUnderstand DC relay coil flyback diodes, polarity, driver protection, built-in suppression, selection data, and release-time trade-offs.
-
06
26-10Limit Switch Wiring: NO, NC and Changeover ContactsIdentify COM, NO and NC from the exact diagram, compare feedback paths, check controller interfaces, and verify actuator and machine response.
-
05
26-10Three-Position Selector Switch Wiring for Hand–Off–AutoBuild a Hand–Off–Auto contact plan, distinguish controller and coil circuits, and check each mode, transition, and restart condition.
-
05
26-10Two-Position Selector Switch Wiring for Hand–Off ControlPlan two-position Hand–Off control from the exact contact table, input or coil circuit, load rating, installation, and verified machine response.
-
05
26-10Relay Contact Arcing: Causes and Suppression MethodsLearn why relay contacts arc, how load type affects suppression, and what to verify before adding an RC network, diode, MOV, or TVS.
-
04
26-10Relay Failure Modes: Coil, Contacts and Mechanical WearClassify relay failures before replacing parts. Review coil supply, contact load, release behavior, socket faults, environment and failure evidence.
-
04
26-10Momentary vs Latching Capacitive Touch SwitchesCompare touch-following and retained outputs. Define event logic, supply and input interfaces, startup, power restoration, indication and testing.
-
04
26-10Flashing vs Steady Indicator Lights for Machine AlarmsChoose flashing or steady machine indications from a clear state matrix. Define operator action, acknowledgement, lamp interfaces and visibility.
-
03
26-10AC vs DC Indicator Lights: Matching the Panel SupplyMatch a panel indicator to its declared AC or DC supply. Check exact variants, polarity, electronic outputs, leakage and the intended signal.
-
03
26-10Indicator Light Symbols in Electrical SchematicsRead indicator lamp and LED symbols with device tags, supply notes, terminal maps and feedback sources. Match the drawing to the actual panel lamp.
- NO.25, SHANGPU 2ND ROAD, QILIGANG INDUSTRIAL PLANT, YUEQING, 325605, ZHEJIANG, CHINA
- +86-577-62628788
- sales@onpow.com
-
Products
-
Application
-
About us
-
Support
-
News
-
WhatsApp
WhatsApp
-
Skype
Skype
-
Wechat
Wechat
-
Email
Email